Max weight
The maximum load allowed for a bicycle is, in other words, the maximum weight that it can normally carry in normal use. Of course, when calculating the load, the weight of both the cyclist himself and the additional load that he carries with him is taken into account.
The permissible load must definitely not be exceeded: even if the bike does not break down immediately, off-design loads can weaken the structure, and an accident can occur at any time. Also note that it is desirable to have a certain weight margin — at least 15 – 20 kg: this can be useful in case of transporting heavy loads and will give an additional guarantee in emergency situations (for example, when a wheel gets into a pit). Considering that the average weight of an adult is about 70 – 80 kg, bicycles with a permissible load
of up to 100 kg can be classified as "lightweights",
from 100 to 120 kg — to the middle category,
more than 120 kg — to "heavy trucks".
Suspension
The presence or absence of a depreciation system on a bicycle, as well as the type of this system.
—
Without depreciation (rigid). In such models, the wheels are fixed directly to the rigid elements of the frame; there are no depreciation devices. Due to this, the design of the bicycle is simple, the weight is small, the cyclist feels all the features of the road topography as much as possible, and the maximum efficiency of pedaling is also achieved, which is important, for example, for road models (see "Destination"). At the same time, structural rigidity is a "double-edged sword". On the one hand, "feeling for the road" is important for
BMX and some mountain models (see "Purpose"); on the other hand, the lack of shock absorption significantly increases the load on both the structure and the rider himself, leads to increased wear, fatigue and some risk of injury on rough roads.
—
Depreciation of the front fork (hard tail). The most popular type of cushioning in adult bikes (see "Age Group"), especially urban and mountain types (see "Purpose"). In accordance with the name, in such bicycles, the shock-absorbing device is installed only on the front fork, while the rear wheel is rigidly fixed. The presence of a shock absorber somewhat increases the weight of the structure and complicates its maintenance, however, the advantages of such a scheme sig
...nificantly outweigh the disadvantages: hard-tails combine good handling, “road feel” and ride comfort, including and on rough terrain.
— Rear fork. Bicycles in which only the rear wheel is damped, while the front wheel is rigidly fixed. The rear shock absorber is designed to provide additional comfort when hitting various bumps, and the absence of a front shock absorber reduces the overall cost of the machine. This option is found mainly in urban models, including electric bicycles (see "Application"); in other varieties, the use of rear shock absorption is not practical.
— Two-suspension (full suspension). Bicycles equipped with shock absorbers on both wheels — a fork in front and a special suspension in the back. Such models are as comfortable as possible for driving on rough terrain, because. They dampen the vibrations felt by the cyclist best and provide the best grip on uneven tracks. At the same time, the presence of a rear shock absorber "eats" part of the energy coming from the pedals, and you have to spend more effort to ride. To avoid this, many two-suspension bikes can be provided with front and rear suspension lockouts (see below), but full suspension complicates the design anyway, increases its weight and price. Therefore, this type of cushioning is relatively rare, mainly in certain varieties of mountain bikes (in particular, for cross-country and freeride; see "Purpose").Suspension type (rear suspension)
Type of rear suspension damping in
full suspension bicycles (see "Suspension"). To date, there are such options:
- Spring-elastomer.
- Spring-oil.
- Air-oil.
- Air.
The first three options are described in detail above in the "Type of cushioning (fork)" section above. In air systems, as the name implies, the working element is air, which acts as both a damper and a shock absorber. This is very convenient due to the ability to change the stiffness of the suspension by adjusting the pressure in the system — the higher the pressure, the harder the damping. However, such shock absorbers are prone to rapid failure due to wear of the seals and require more careful maintenance than similar air-oil shock absorbers in many respects.
Tyre
Tyre model supplied with the bike as standard. Different tyres have different purposes and characteristics; knowing the tyre model, you can clarify these points and check how they correspond to your wishes. This is especially important when choosing a machine for serious cycling.
Cast wheels
Light-alloy wheels of a monolithic design, cast in special molds from aluminium, less often from titanium. Bicycles with
alloy wheels are characterized by increased resistance to oncoming air flows, strength and durability, and aesthetic appeal. At the same time, “casting” is less resistant to side gusts of wind, has poor maintainability and is very expensive. In the mass segment, alloy wheels are found mainly on board city and road electric bicycles; in narrower niches, specialized racing bike models are equipped with monolithic wheels.
Front rotor
Front rotor.
The front disc brake rotor is a perforated metal plate attached to the wheel hub. The reduction in speed of the bike occurs as a result of the compression of the brake disc by the pads, which are driven by cable tension (in mechanical type systems) or by means of a hydraulic circuit (in hydraulic disc brakes). The diameter of the front rotor can vary from 140mm to 220mm. The higher the number, the more efficient the brake is.
Rear rotor
Rear rotor.
An element of a disc brake system mounted on the hub of the rear wheel of a bicycle. It is to him that the pads are pressed when the brake lever is pressed. The use of a rotor ensures high braking efficiency. And it is higher, the larger the diameter of the rear rotor. Disc rotors are available in sizes 140, 160, 180, 185, 203 and 220 mm.
Chain model
Model of the chain supplied as standard with the bike. For details on the value of the Model parameter for any part, see Cassette Model
Battery capacity
The capacity of the battery that the e-bike is equipped with (see "Application"), expressed in ampere-hours.
The battery capacity directly affects the operating time on a charge and, accordingly, the power reserve. However, in fact it hardly makes sense to evaluate these parameters by the number of ampere-hours. Firstly, the actual battery life will depend not only on the characteristics of the battery, but also on the power of the engine (which determines the power consumption of the machine). Secondly, the actual amount of energy stored in the battery depends not only on the capacity in ampere-hours, but also on the rated voltage; a more reliable unit in this sense is watt-hours, see Battery Capacity below for more details. So when choosing, it is better to focus not so much on the number of ampere-hours, but on the power reserve directly claimed by the manufacturer.
